Search found 147 matches
- 06 Sep 2015 09:50 pm
- Forum: Engine, transmission, manual gearbox, variomatic
- Topic: What engine do i have ( 1.7 DL 1987 )
- Replies: 10
- Views: 10131
Re: What engine do i have ( 1.7 DL 1987 )
Does make much sense, how can only be not for a particular model? That means it fits all cars but one! AFAIK there is only one type of 1.7 340 engine, the B172K. No. Two types, old and new. 124 and 125 tooth timing belt. If you cab spot the difference on the outside I don't know! But I would think ...
- 06 Sep 2015 09:48 pm
- Forum: Suspension, steering, wheels, brakes
- Topic: Urgent ! Rear wheel cylinder
- Replies: 13
- Views: 12298
Re: Urgent ! Rear wheel cylinder
Would there be much trouble if one uses 340 cylinders on a 360, or vice versa?
- 31 Aug 2015 07:44 am
- Forum: Tell us more about your project Volvo 300
- Topic: 1.9 Carb 1985 Volvo 360 GLS - Bought on 16/11/2014 5.30PM
- Replies: 96
- Views: 53023
Re: 1.9 Carb 1985 Volvo 360 GLS - Bought on 16/11/2014 5.30P
No you can not. Try bleeding one when the bleednipple is on the bottom.zack360 wrote:Hello all, quick question, can I replace left hand side brake calliper with right hand side? The only difference is the brake hose hole..it will face backward.
Thanks
- 18 Aug 2015 08:30 am
- Forum: Engine, transmission, manual gearbox, variomatic
- Topic: b204e swap
- Replies: 6
- Views: 6870
Re: b204e swap
The b204 shortblock is different, so you would need to make some motormounts. You can put the head on the b200e but that would involve changing or modifing the pistons. And getting a a right timingbelt kit for the swap. The stock b200e full system can not adapt, so modifing or changing has to be don...
- 14 Jul 2015 12:32 pm
- Forum: Suspension, steering, wheels, brakes
- Topic: Help find a part
- Replies: 8
- Views: 6432
Re: Help find a part
Wheel Hub?
- 01 Jul 2015 02:16 pm
- Forum: Engine, transmission, manual gearbox, variomatic
- Topic: EZK / LH2.4 360 crank sensor
- Replies: 2
- Views: 4510
Re: EZK / LH2.4 360 crank sensor
Renix is 2-wire, lh2.4 is 3-wire. You can easily make a bracket to hold the 940 sensor. Same idea as the original bracket but then weld a nut 90 degrees turned on the bracket. Spacing between sensor and flywheel is critical.
- 30 Jun 2015 12:08 pm
- Forum: Tell us more about your project Volvo 300
- Topic: Nolan's 340 pick up D-project F7p (need help for Vss)
- Replies: 59
- Views: 39189
Re: Nolan's 340 pick up D-project F7p (need help for Vss)
Looking at you pictures, why does the idle air valve have a airfilter on it? It should regulate the amount of air going around the throttleplate at idle.
- 20 Jun 2015 03:38 pm
- Forum: Engine, transmission, manual gearbox, variomatic
- Topic: Injection wiring grommet
- Replies: 16
- Views: 15273
Re: Injection wiring grommet
Yes, you are right!Ride_on wrote:I shouldn't have any problem with wiring as my car is completely stripped, just going use wire from the copious 940 loom. But is my assumption correct about the GLT wiring going down the the fuel sender grommet under the back seat?
- 19 Jun 2015 09:48 pm
- Forum: Suspension, steering, wheels, brakes
- Topic: wheel stud sizes
- Replies: 5
- Views: 5698
Re: wheel stud sizes
I'd rather not drill the holes. Does anyone know the diameter of the original wheel studs? I have found a supplier for 12,8 and 13,0 (and 14,2 and 14,3). I was sceptical at first about drilling, but when you put the hub under a pillar drill it goes right through and getting the new ones in is easy....
- 19 Jun 2015 09:44 pm
- Forum: Tell us more about your project Volvo 300
- Topic: My new barn find
- Replies: 13
- Views: 11879
Re: My new barn find
It being a 88 GLE it probably has injection, and after 12 years I would not be suprised if the injectors are gunked up with old fuel. The fuel pump and filters will be aswell.. I would drain and flush the tank, replace all the hoses and filters (those cotton braided hoses dry and brake are the worst...
- 17 Jun 2015 01:15 pm
- Forum: Tell us more about your standard Volvo 300
- Topic: Trallas Volvo 360GLS
- Replies: 67
- Views: 46679
Re: Trallas Volvo 360GLS
That is part of the renix system, which only came on the 300 series! B19a is carburetted with point ignition, b21et had kjet with point ignition if I'm right. I've heard that you might be able to use a cranksensor from a Volvo 440, 460 or 480. But not sure of that.
- 13 Jun 2015 11:27 pm
- Forum: Engine, transmission, manual gearbox, variomatic
- Topic: Injection wiring grommet
- Replies: 16
- Views: 15273
Re: Injection wiring grommet
LH2.4 harness goes through, you can even use the grommet on the harnessRide_on wrote:it overlaps >50% with the air box although there is a bit of clearance. Hopefully works, saves me cutting holes. Lets see if I can get LH2.4+EZK through it.
Airbox probably has to come out again, hmm.
- 13 Jun 2015 10:55 pm
- Forum: Engine, transmission, manual gearbox, variomatic
- Topic: Injection wiring grommet
- Replies: 16
- Views: 15273
Re: Injection wiring grommet
That should be the one, so they did move the hole in the bulkhead.
- 13 Jun 2015 10:54 pm
- Forum: Tell us more about your project Volvo 300
- Topic: Nolan's 340 pick up D-project F7p (need help for Vss)
- Replies: 59
- Views: 39189
- 13 Jun 2015 08:28 pm
- Forum: Tell us more about your project Volvo 300
- Topic: Nolan's 340 pick up D-project F7p (need help for Vss)
- Replies: 59
- Views: 39189
Re: Nolan's 340 pick up D-project F7p (need help for Vss)
You mean i have to cut around the old dash resistors and connect it to the + ? I've found a pic from my dash: http://img15.hostingpics.net/pics/33905844e7e9a6938219fe7066e9be0f89f3430.jpg It's from a 440 Do you think i can put a 5v module reducer like this: http://www.ebay.fr/itm/DC-DC-KIM-055L-9-3...