Page 1 of 12
Restoring To Standard 360 GLE
Posted: 12 May 2014 02:55 am
by zack360
Hi all,
I am having trouble to find this thing.. anyone have it in good condition? Thanks
Re: Restoring To Standard 360 GLE
Posted: 12 May 2014 07:58 am
by volvomania
Is it the actual dash, the plastic surround that houses the switches or just the instrumentcluster you want?
Re: Restoring To Standard 360 GLE
Posted: 12 May 2014 11:09 am
by zack360
It's the plastic sounding the meter, the instrument and the light knob.
Re: Restoring To Standard 360 GLE
Posted: 13 May 2014 07:36 am
by volvomania
That should be quite easy to find in the UK (RHD).
On the continent they are all different (LHD) and unuseable for you.
Why don't you put a posting in the "Volvo 300 series: demand" section?
I am sure that postage to Malaysia will be more expensive than the part.
Re: Restoring To Standard 360 GLE
Posted: 13 May 2014 06:55 pm
by classicswede
I will have one available next week off my JIG car but as RJ says postage will certainly cost more than the part
Re: Restoring To Standard 360 GLE
Posted: 14 May 2014 04:19 am
by zack360
Ok..thanks mate, by the way can you classicswede post the picture if you have it? it think it's weight is less than 500 gram..can you find out the the total postage ? and if you have the bracket for the rear bumper can you post it too?
Re: Restoring To Standard 360 GLE
Posted: 14 May 2014 09:11 am
by classicswede
is it the L shaped rear bumper brackets you need?
Re: Restoring To Standard 360 GLE
Posted: 14 May 2014 08:06 pm
by Ride_on
saloon or hatch? different bumper mounts.
Re: Restoring To Standard 360 GLE
Posted: 15 May 2014 02:59 am
by zack360
Classic swede: No it's the plastic that is screwed to the body and you just slide the rear bumper to it so that the bumper wont hang..ya know what i'm sayin..

there are two pieces. It's almost the same shape as front bumper, only slightly bigger.. i got 1 member post it to me earlier this year..i think it's mchudd or something. I'll try to post the pic.
Volare Volvo 360!!
Re: Restoring To Standard 360 GLE
Posted: 15 May 2014 03:27 am
by zack360
Here is the pic
Re: Restoring To Standard 360 GLE
Posted: 15 May 2014 07:52 pm
by Logan360
I have everything you need, in good condition too. The dash surround has a crack at the far lower left but it is not visible with the cluster in place. And I have a pair of rear bumper plastic mounts too.
Re: Restoring To Standard 360 GLE
Posted: 16 May 2014 03:39 am
by zack360
Logan360 wrote:I have everything you need, in good condition too. The dash surround has a crack at the far lower left but it is not visible with the cluster in place. And I have a pair of rear bumper plastic mounts too.
Thanks Logan, can you possibly post the picture of the dash. just to make sure it's the right thing

before you post it.
Re: Restoring To Standard 360 GLE
Posted: 16 May 2014 07:01 am
by Logan360
Pm me your email as I can't upload photos to the forum.
Re: Restoring To Standard 360 GLE
Posted: 16 May 2014 07:35 am
by zack360
pm to you just now.
Re: Restoring To Standard 360 GLE
Posted: 23 Jun 2014 04:12 pm
by zack360
Hi again,
I have trouble to start the car could it be the fuel relay? i checked the fuel pump it's running perfect. At first i thought it was the pump because when it's in ignition there were no noise coming from the pump. I test it on my car battery, the motor spins well, i got a replacement relay from 240 is it compatible? before i remove the pump i also checked the hose from the pump to fuel filter on the engine bay but there were no fuel coming out. One question does my model (360 GLE) have two fuel pump? as i checked there is only one on the bottom of the car. When i checked under the passenger sit, there is a round cap and after i remove it there were no pump only float. Need advice.. and may i know where is the fuel pump relay located, here is the picture..