Project T5 360.

For drift/rally/builds cars projects, engine conversions etc...
Describe your plans, project(s) evolution, works progress and final result!
Post Reply
mat_91
Posts: 636
Joined: 07 Oct 2009 08:50 pm
Location: nottinghamshire

Re: Project T5 360.

Post by mat_91 » 29 Oct 2011 08:04 pm

cool work i love rebuilding engine and
Ld50 wrote:
wiganer31 wrote:Valves all in.. Lost one of the little things that hold it all in position... Found it on the magnet of a speaker 2 days later.
there called collets fella
Image

Ld50
Posts: 96
Joined: 03 Nov 2010 11:00 am

Re: Project T5 360.

Post by Ld50 » 30 Oct 2011 02:28 pm

mat_91 wrote:cool work i love rebuilding engine and
Ld50 wrote:
wiganer31 wrote:Valves all in.. Lost one of the little things that hold it all in position... Found it on the magnet of a speaker 2 days later.
there called collets fella
Yeah, I always forget.

Was pretty scared about the head bolt tensions. Had to get 2 meters of pipe onto the breaker bar to get it up to the angle....

Still pending on the parts from Sweden. As it is now I'm not sure how much more money is going into the Supra so I'm holding off 'till then...

Ld50
Posts: 96
Joined: 03 Nov 2010 11:00 am

Re: Project T5 360.

Post by Ld50 » 27 Jan 2012 02:40 pm

Been really slack lately.
(Paying off parts to work, and drowning income into the supra)

Ordering parts from sweden hopefully in 2 weeks but I have to get them sent to relatives in Finland first as they don't ship to australia (bummer)

I'll start on pulling out the engine this weekend as I finally managed to afford an engine crane over the christmas break :lol:

Having been 30+ over the past 2 months and it's going to be 42 tomorrow I'm not sure how it's going to go down, hopefully will have the engine out and the 5 banger fully back together to start thinking of mounts and intercooler + piping etc.

Regards -
Jere.

Ld50
Posts: 96
Joined: 03 Nov 2010 11:00 am

Re: Project T5 360.

Post by Ld50 » 28 Jan 2012 05:34 am

Got the workspace cleaned a bit, and a bit more recent photo of the motor.. Nothing much more done to it since last time.

Image
Image

Ld50
Posts: 96
Joined: 03 Nov 2010 11:00 am

Re: Project T5 360.

Post by Ld50 » 29 Jan 2012 08:10 am

Got the car turned around and engine crane assembled.
No work on the 5cyl as I'm getting a cambelt tension pulley and a water pump next week so it should be completed during the week. With the mounts I've decided to pull the motor out with the mounts attached then pull them off and see what I can do with them on the new motor.

Image

joe1980
Posts: 4
Joined: 18 Sep 2011 10:32 pm

Re: Project T5 360.

Post by joe1980 » 29 Jan 2012 05:48 pm

Getting there then what sump are you going too use are you having manifolds made (inlet and exhaust) or you got something lined up

Ld50
Posts: 96
Joined: 03 Nov 2010 11:00 am

Re: Project T5 360.

Post by Ld50 » 30 Jan 2012 05:31 am

joe1980 wrote:Getting there then what sump are you going too use are you having manifolds made (inlet and exhaust) or you got something lined up
Stock sump and manifolds at the moment. The turbo will most likely hug the brake master or the chassis.. Intake manifold should be fine for fitment but might be looking at getting a plenum made if I get the stronger box and do go with more power. I haven't looked into if the sump will hit anything but the b200 sump seems a bit bigger so hopefully no dramas.

User avatar
Speedy88
Posts: 4057
Joined: 04 May 2009 11:52 pm
Location: Bristol

Re: Project T5 360.

Post by Speedy88 » 30 Jan 2012 07:22 am

Looking good man, look forward to seeing this finished :D
'88 340 Williams (Sold)
'85 360 GLS - Drift project (Sold)
'77 Colt Sigma
'96 940 Drift project

Ld50
Posts: 96
Joined: 03 Nov 2010 11:00 am

Re: Project T5 360.

Post by Ld50 » 30 Jan 2012 12:27 pm

Speedy88 wrote:Looking good man, look forward to seeing this finished :D
Yeah pace is going to pick up now. Sold my old whip to my ex workmate so he should be paying that off to me shortly. Got everything pretty much sourced out just need the time and money. It's starting to get a bit cooler now so I can work on her a bit more. Engine coming out before the weekend hopefully :D

Ld50
Posts: 96
Joined: 03 Nov 2010 11:00 am

Re: Project T5 360.

Post by Ld50 » 11 Feb 2012 12:42 pm

Progress!

Got the engine pretty much fully done, I had no clue to the timing cause the illustration that I got (both marks at 12 o'clock), which was the same as in the haynes manual, were wrong. I figured it was to the notches on the top cover where it comes down on the front a bit which is 2 and 10 o clock (I presume). Valves were clearing pistons so the worst that can happen is it'll run like shit or won't run at all, but won't damage the engine.
New water pump, pulleys and belt.. Rather be safe than sorry right :lol:

Image
Image
Image

Tomorrow I'll be putting on the sump, just have to find the new o-rings and all that. Then to rip out the old 4 banger.

Alan M
Posts: 13
Joined: 15 Jan 2012 11:47 am

Re: Project T5 360.

Post by Alan M » 14 Feb 2012 11:57 am

To get the inlet manifold facing the correct way for rwd applications you can use the manifold from the newer generation of ford/Volvo derived turbo t5 engines and make an adaptor flange to mount a throttle body of your choice depending on what management you intend to use.

User avatar
Speedy88
Posts: 4057
Joined: 04 May 2009 11:52 pm
Location: Bristol

Re: Project T5 360.

Post by Speedy88 » 14 Feb 2012 12:19 pm

Nice, make sure you turn the engine over at least 4 times (5 to be safe) to make sure the valves don't touch at any point.
'88 340 Williams (Sold)
'85 360 GLS - Drift project (Sold)
'77 Colt Sigma
'96 940 Drift project

Ld50
Posts: 96
Joined: 03 Nov 2010 11:00 am

Re: Project T5 360.

Post by Ld50 » 14 Feb 2012 02:26 pm

Alan M wrote:To get the inlet manifold facing the correct way for rwd applications you can use the manifold from the newer generation of ford/Volvo derived turbo t5 engines and make an adaptor flange to mount a throttle body of your choice depending on what management you intend to use.
Yeah, the intake side won't be a problem. Brake booster and chassis will be my first main concerns..
Speedy88 wrote:Nice, make sure you turn the engine over at least 4 times (5 to be safe) to make sure the valves don't touch at any point.
Spun it a fair few times 'cause dad, as usual, thought I couldn't do it.. I'll still make sure before I start it when she's in but spun fair easily all the way through so I'm pretty confident :lol:

Regards -
Jere

Ld50
Posts: 96
Joined: 03 Nov 2010 11:00 am

Re: Project T5 360.

Post by Ld50 » 12 Mar 2012 11:15 am

Got some work in on the weekend, was really hot so I only had a few hours in the arvo.

Image

Was a bit of a mission to get that engine out, seeing as we took the bellhousing with it we had to move the prop shaft and gearbox back to get it the prop shaft out of the bellhousing. I think this would've been better to do with a 240 or something that has a front mounted box and more room in the engine bay :lol:

User avatar
Speedy88
Posts: 4057
Joined: 04 May 2009 11:52 pm
Location: Bristol

Re: Project T5 360.

Post by Speedy88 » 12 Mar 2012 11:32 am

Nice to see steady progress on this :)
'88 340 Williams (Sold)
'85 360 GLS - Drift project (Sold)
'77 Colt Sigma
'96 940 Drift project

Post Reply