cutting springs

Front axle, springs, shock absorbers, wheels, bearings, calipers, drums...
Tuning: suspension, discs, alloys upgrade...
NO parts requests here, please use our V3M BUY & SELL corner
rems
Posts: 120
Joined: 16 Jan 2009 02:11 am
Location: devon

cutting springs

Post by rems » 11 Feb 2009 01:04 am

right .... im looking to lower my 340 by about 40mm but im on a budget :(

i have looked for springs n they fair pricey just for the springs

i have been told to just cut the springs :?

however i have read that this isnt the most ideal thing to do but it can be done, so is it adviseable?

if people say yea then whats the best way to do it so that i do a decent job of it so that it will lower by 40mm and i wil get it the same on both sides

User avatar
filthyjohn
*** V3M DONOR ***
Posts: 2693
Joined: 12 Sep 2006 09:07 pm
Location: Sunderland, Ringpiece Of England

Re: cutting springs

Post by filthyjohn » 11 Feb 2009 01:53 am

It'll be fine as long as you don't cut too much off. 2 coils off a standard spring is about max if you want the spring to remain captive when you jack it up (an MOT requirement), and should see it down 2inches or so. The only dangers are scraping the bottom of the car on things, (shouldn't be a problem at -2"), and the danger of the actual choperation. Get some good spring compressors or you may end up getting pretty messed up by a flying spring.
'87 Nissan Sunny
'95 945 LPT
'90 340 3dr
'87 360 GLT
'87 765 TIC
'75 Manta A
'70 Rover P5 V8
'67 MGB GT
'62 amazon 2dr

User avatar
jtbo
Posts: 5805
Joined: 23 Jul 2004 03:50 am
Location: Finland, middle of nowhere
Contact:

Re: cutting springs

Post by jtbo » 11 Feb 2009 02:13 am

Springs are odd, if you remove coils it will become stronger so dampers can get weak and then you would have kangaroo in a car, but perhaps not yet with 2 coils, was it only 25% stiffer? Can't remember, I have calculator made for that, though:

Installable software:
http://www.janiervast.com/rfactor/Calcu ... taller.zip

Excel spreadsheet (this one has damper calculations and such too):
http://www.janiervast.com/rfactor/Calcu ... lators.xls
Volvo 360GL -88 -under restoration-
Volvo 343DL vario -81 -running- Image
Volvo 240 Diesel -83 -undecided-
Citroen ZX Dturbo -97 -daily- ImageImage

User avatar
Chris_C
*** V3M DONOR ***
Posts: 9600
Joined: 18 Jun 2004 11:53 pm
Location: South Coast, UK

Re: cutting springs

Post by Chris_C » 11 Feb 2009 11:12 am

How will the springs get stronger Jani? They'll still be soft as s**t, just less of them so it'll bottom out quicker. Rems, if you want more power and an engine swap eventually, this will make your car handle worse.
'89(G) 340 GLE B172k
'03 S60 D5 SE, '91 (J) MX5, 1954 Cyclemaster
Ex:
'89(F) 340 GL F7R (ex B172k) - Fake -> SBKV 300 Runner Up 08, 12; '91(H) 340 GL B14.4E - Kar; '88(F) 360 GLT B200E - Jet -> BKV 300 Runner Up 09; '89(G) 360 GLT B200E - Beast

User avatar
SteveP
*** V3M DONOR ***
Posts: 7933
Joined: 21 Sep 2004 12:45 pm
Location: Coventry, UK

Re: cutting springs

Post by SteveP » 11 Feb 2009 12:53 pm

Jani is right IIRC... they will be a little harder than stock. Ali's car had cut front springs and with uprated dampers and lowering blocks handled 10x better than stock. Although it did prematurely wear out the front shocks, which would happen with any shorter spring unless you match the shock absorber length anyway
1989 - Volvo 360 GLT
1985 - Volvo 360 GLS
2008 - Volvo S60 SE Lux

User avatar
filthyjohn
*** V3M DONOR ***
Posts: 2693
Joined: 12 Sep 2006 09:07 pm
Location: Sunderland, Ringpiece Of England

Re: cutting springs

Post by filthyjohn » 11 Feb 2009 12:58 pm

Something to do with the remaining metal having to deflect further for a given amount of travel. The proper lowering springs really showed up my worn front dampers anyway, so they'd need refilling or upgrading.
'87 Nissan Sunny
'95 945 LPT
'90 340 3dr
'87 360 GLT
'87 765 TIC
'75 Manta A
'70 Rover P5 V8
'67 MGB GT
'62 amazon 2dr

User avatar
trabitom99
*** V3M DONOR ***
Posts: 4398
Joined: 06 Jan 2007 02:38 pm
Location: Bonn, Germany

Re: cutting springs

Post by trabitom99 » 11 Feb 2009 12:59 pm

Cutting front springs would automatically relieve you of your insurance cover in Germany. But then, quite a few other "mods" do too ;-) (if you don't declare them)

Tom
343 GL Touring B14.1E CVT (155) 98000kms 1980 (sold)
343 L Junior B14.3E MT4 (155) 229000kms 1981 (scrapped)
343 DLS B19A MT4 (155) 167900kms 1982
360 GL Injection B200F MT5 (231) 348598kms 1988 (scrapped)
360 GLT B200F MT5 (302) 230000kms 1988

User avatar
OapEM
Posts: 488
Joined: 29 Nov 2008 06:49 pm
Location: Sunderland

Re: cutting springs

Post by OapEM » 11 Feb 2009 01:23 pm

/\ Same here I think lol

John YHPM
Get rich or die tryin'!

User avatar
Chris_C
*** V3M DONOR ***
Posts: 9600
Joined: 18 Jun 2004 11:53 pm
Location: South Coast, UK

Re: cutting springs

Post by Chris_C » 11 Feb 2009 03:20 pm

I'm confused... I will sit quietly in the corner with some textbooks and a pen and paper! Will return later :lol:
'89(G) 340 GLE B172k
'03 S60 D5 SE, '91 (J) MX5, 1954 Cyclemaster
Ex:
'89(F) 340 GL F7R (ex B172k) - Fake -> SBKV 300 Runner Up 08, 12; '91(H) 340 GL B14.4E - Kar; '88(F) 360 GLT B200E - Jet -> BKV 300 Runner Up 09; '89(G) 360 GLT B200E - Beast

volvosneverdie
*** V3M DONOR ***
Posts: 9143
Joined: 11 Nov 2008 04:22 pm
Location: Newcastle Upon Toon

Re: cutting springs

Post by volvosneverdie » 11 Feb 2009 03:27 pm

OapEM wrote:/\ Same here I think lol

John YHPM
Surely not.

Cut springs, as long as theyre in one piece are just springs arnt they?
If they go through an mot, surely they dont invalidate your insurance.
Image

User avatar
filthyjohn
*** V3M DONOR ***
Posts: 2693
Joined: 12 Sep 2006 09:07 pm
Location: Sunderland, Ringpiece Of England

Re: cutting springs

Post by filthyjohn » 11 Feb 2009 03:30 pm

As long as they remain captive they'll pass MOT. But insurance may try to invalidate if you fail to declare putting a sticker on the gearknob. :roll:
'87 Nissan Sunny
'95 945 LPT
'90 340 3dr
'87 360 GLT
'87 765 TIC
'75 Manta A
'70 Rover P5 V8
'67 MGB GT
'62 amazon 2dr

volvosneverdie
*** V3M DONOR ***
Posts: 9143
Joined: 11 Nov 2008 04:22 pm
Location: Newcastle Upon Toon

Re: cutting springs

Post by volvosneverdie » 11 Feb 2009 03:33 pm

filthyjohn wrote:As long as they remain captive they'll pass MOT. But insurance may try to invalidate if you fail to declare putting a sticker on the gearknob. :roll:
really should declare my mods then.
Drop and wheels must be good for bumping the premium a few hundred quid.
Image

User avatar
filthyjohn
*** V3M DONOR ***
Posts: 2693
Joined: 12 Sep 2006 09:07 pm
Location: Sunderland, Ringpiece Of England

Re: cutting springs

Post by filthyjohn » 11 Feb 2009 03:42 pm

Most companies are cool with wheels and a slight drop, might not raise the premium if you're lucky.
'87 Nissan Sunny
'95 945 LPT
'90 340 3dr
'87 360 GLT
'87 765 TIC
'75 Manta A
'70 Rover P5 V8
'67 MGB GT
'62 amazon 2dr

User avatar
Chris_C
*** V3M DONOR ***
Posts: 9600
Joined: 18 Jun 2004 11:53 pm
Location: South Coast, UK

Re: cutting springs

Post by Chris_C » 11 Feb 2009 04:20 pm

Right, I *think* I've got my head around it.

Follow me for a minute, and see if this makes any sense. I'm trying to think of an example to parallel it with, but can't at the moment.

Jani, your xls calulator shows the spring rate for a coil spring under compression,

k = Gd^4
8nD^3

Where G is rigidity of the material,
d wire diamter
n no of *active* coils, i.e. the actual working ones in a spring (I'll come back to this)
D mean coil diameter

So, if we remove everything from that equation as a constant (q), we get

k= q * 1/n

Meaning, if we have 2 active coils, k = q/2 and if we have 1 active coil, k=q

So, less coils = more spring rate.

BUT

Spring rate does not have units of force, it is force/distance hence a torque. Hookes law comes in, and we can get to force (and therefore the amount of force needed to move the wheel on the end of the suspension) by

F= kx

where x is displacement, in our case the distance the spring moves or is compressed by

But, as the spring is now shorter (in the theoretical argument of a 2 coil spring vs a 1 coil spring, the 1 coil spring is half the size) so if can only move half the distance. Giving that the amount of force to move the suspension for a chopped spring is exactly the same as it is for a stock spring.

The only thing that will be of any effect here is that you will remove more than the active coils, you'll also remove the inactive coils at the end of the spring (the ones that stop the end rubbing the spring seat) and the fact that as you cut the coil, if you get it hot you'll loose the tempering that gave that spring it's stiffness in the first place, and make it softer than it currently is (which isnt very, as wear will also soften it from it's original tempering.

Does that make sense to anyone else? Or have I got the wrong end of the stick.
'89(G) 340 GLE B172k
'03 S60 D5 SE, '91 (J) MX5, 1954 Cyclemaster
Ex:
'89(F) 340 GL F7R (ex B172k) - Fake -> SBKV 300 Runner Up 08, 12; '91(H) 340 GL B14.4E - Kar; '88(F) 360 GLT B200E - Jet -> BKV 300 Runner Up 09; '89(G) 360 GLT B200E - Beast

User avatar
trabitom99
*** V3M DONOR ***
Posts: 4398
Joined: 06 Jan 2007 02:38 pm
Location: Bonn, Germany

Re: cutting springs

Post by trabitom99 » 11 Feb 2009 04:48 pm

Chris, have you ever considered applying for a job in a German company ;-) ?

Tom
343 GL Touring B14.1E CVT (155) 98000kms 1980 (sold)
343 L Junior B14.3E MT4 (155) 229000kms 1981 (scrapped)
343 DLS B19A MT4 (155) 167900kms 1982
360 GL Injection B200F MT5 (231) 348598kms 1988 (scrapped)
360 GLT B200F MT5 (302) 230000kms 1988

Post Reply