REAR BUMPER REMOVAL???

Rust problems and repairs, leaky sunroof... Battery, starter, lights, fuses, airco, heating unit, stereo... | Tuning: custom spoilers & bodykits, fiberglass parts...
NO parts requests here, please use our V3M BUY & SELL corner
Edokun91
Posts: 75
Joined: 17 Oct 2010 07:13 pm

REAR BUMPER REMOVAL???

Post by Edokun91 » 04 May 2011 07:52 pm

Hey guys,
I'm in the process of removing my tow bar, got the spacer plates off to find it held in place by what seems to be the bumper. Do we know where abouts exactly the remaining bolts are/spanner sizes etc.? I've had a look at a few threads but not found anything that's made much sense.

Tips/a runthrough would be much appreciated! :360:

Ride_on
Posts: 2262
Joined: 26 May 2009 05:34 pm
Location: Belfast, N. Ireland

Re: REAR BUMPER REMOVAL???

Post by Ride_on » 06 May 2011 09:12 pm

The rear bumper brackets are held on (each) by 2 bolts that go through the chassis rails above the rear of the leaf spring shackles. If its a saloon there may also be a stabiliser that bolts into the section under the light clusters. All the nuts will be very difficult to remove, removed some recently can't remember the size, but you need to clean off the threads well, wire brush on drill, as much as possible to have any hope of removing them without snapping.

The tow bar, is it a OE one.. photos?
1980 345 DL_______1987 360 GLE (project car restored to GLT spec and B230FT'd)
1984 360 GLT______1987 360 GLT
1983 360 GLS______1989 360 GLE
1985 340 GL_______1986 340 1.4
1985 360 GLS______1995 940 SE 2.3 Turbo Estate (daily)
1987 340 GL 1.7

pettaw
*** V3M DONOR ***
Posts: 1673
Joined: 15 Aug 2004 07:39 pm
Location: London, UK

Re: REAR BUMPER REMOVAL???

Post by pettaw » 08 May 2011 09:46 am

Yeah the rear bumper bolts are very long and will be very dirty/rusty. You'll need to clean off the threads very carefully and then put WD-40 to soak, then clean the threads off again! Then you can wind them out keeping your fingers crossed that they don't snap. If they start getting stiff, then wind back in to free off and then use more WD-40 and brushing to move the dirt again. I think the size is 13mm.

User avatar
L14MNP
Posts: 1340
Joined: 26 May 2010 09:15 pm
Location: Sunderland/Durham

Re: REAR BUMPER REMOVAL???

Post by L14MNP » 08 May 2011 12:47 pm

I never bothered removing the brackets from the car at first as the bolts didn't want to know so I unbolted them from the carrier bar instead. Can you not just do that?

I needed to clean the underseal off the legs though so yesterday i took the plunge and removed them. They weren't as bad ad made out. Three out of the four bolts snapped but imo that's a good thing!

It means I can replace them with something that's not 28 years old!

If the back of your car looks mine it is a bit easier to swing the ratchet though! :lol:

Image
STREETO WITHDRAWL
INTO BURNOUTSsince1982

User avatar
volvodspec
Posts: 1921
Joined: 06 Dec 2008 09:35 pm
Location: Netherlands.
Contact:

Re: REAR BUMPER REMOVAL???

Post by volvodspec » 08 May 2011 02:58 pm

slide your hand horizotally in from the wheelside; easy acces to the nut and you can use a normal wirebrush to clean the threads a bit.

unbolting speaks to itself, use a wrench on the outer sides and a ratchet on the inner sides. easy peazy, don't really understand why this keeps giving problems (at V3C aswell) i might have broken a few of the bolts on the ones i took off a car (at least 13, 14 maybe even 15 bumpers) but they all went off without too much hassle or problems.

Edokun91
Posts: 75
Joined: 17 Oct 2010 07:13 pm

Re: REAR BUMPER REMOVAL???

Post by Edokun91 » 08 May 2011 04:08 pm

ahh cheers people, feeling confident enough to commit to it now i recon lol the cars an '84 but not even 50k on the clock so hoping the bolts will be in better shape than on other 360s..hoping...
I'll let you know what happens :360:

User avatar
L14MNP
Posts: 1340
Joined: 26 May 2010 09:15 pm
Location: Sunderland/Durham

Re: REAR BUMPER REMOVAL???

Post by L14MNP » 08 May 2011 04:29 pm

<70K 1984 360 that lay unsued in a garage for 15 years here.

Don't expect too much! :lol:
STREETO WITHDRAWL
INTO BURNOUTSsince1982

Edokun91
Posts: 75
Joined: 17 Oct 2010 07:13 pm

Re: REAR BUMPER REMOVAL???

Post by Edokun91 » 24 May 2011 01:26 pm

ok so i got it all off no problems what so ever! BUT, the plastic bumper will now not go on as it was pretty much just the towbar holding it to the car, there are the two slidy bits on both rear wings that go in but they dont hold it on properly :? is there a part im missing that was replaced by the towbar when it got put on or am i just being retarded? guess i'll have to drive without a rear bumper for the time being. HALP! :360:

Edokun91
Posts: 75
Joined: 17 Oct 2010 07:13 pm

Re: REAR BUMPER REMOVAL???

Post by Edokun91 » 25 May 2011 10:53 pm

bump!

User avatar
Hell Driver
Posts: 1415
Joined: 18 Aug 2009 09:58 pm
Location: Doncaster UK

Re: REAR BUMPER REMOVAL???

Post by Hell Driver » 25 May 2011 11:42 pm

Are the plastic bits broken on the car or the bumper? Should hold it unless a bit is broken.
360 GLE Saloon (D 86)
360 GLS (A 84)
343 DL (W 80) :-)
340 GL 1.7 (G 89)
360 GLS (Y 83)
440 Turbo (J 92)
Transit Tipper 125 T350 (02)Alive Again!
Transit Tipper Smiley face Q reg
Mitsubishi Colt 1.1 (54)
R.I.P. 77 343 DL vario :-(

Edokun91
Posts: 75
Joined: 17 Oct 2010 07:13 pm

Re: REAR BUMPER REMOVAL???

Post by Edokun91 » 26 May 2011 06:28 pm

nah they are fine:s are you sure? theres noway it can be held on by two small slidey clips on each side, there's nothing supporting the middle atall, surley i'm missing an original bracket or something? :cry:

User avatar
Chris_C
*** V3M DONOR ***
Posts: 9600
Joined: 18 Jun 2004 11:53 pm
Location: South Coast, UK

Re: REAR BUMPER REMOVAL???

Post by Chris_C » 26 May 2011 07:35 pm

The middle of the rear bumper has some 12" long metal spikey bits that go under the boot floor... take a picture of what you took off and we can point you at them ;)
'89(G) 340 GLE B172k
'03 S60 D5 SE, '91 (J) MX5, 1954 Cyclemaster
Ex:
'89(F) 340 GL F7R (ex B172k) - Fake -> SBKV 300 Runner Up 08, 12; '91(H) 340 GL B14.4E - Kar; '88(F) 360 GLT B200E - Jet -> BKV 300 Runner Up 09; '89(G) 360 GLT B200E - Beast

Edokun91
Posts: 75
Joined: 17 Oct 2010 07:13 pm

Re: REAR BUMPER REMOVAL???

Post by Edokun91 » 26 May 2011 07:45 pm

hmm i guess im missing them then :( I mean it'd be pretty obvious if they were there lol. here ya go, all that i had was towbar (which has two sort of brackets that go and bolt under the car) and the bumper, the wires hanging down are the number plate lights. Image

User avatar
volvodspec
Posts: 1921
Joined: 06 Dec 2008 09:35 pm
Location: Netherlands.
Contact:

Re: REAR BUMPER REMOVAL???

Post by volvodspec » 26 May 2011 09:46 pm

you'll need a rear bumper without towbar for the brackets holding the middle section up. it is mounted on the same place on the chassis beams like the towbar

why do you want to remove the towbar? simplest solution would be to bolt it back together, you could allways cut the towing arm + ball off so you're left with the beam and the mounting points

User avatar
Chris_C
*** V3M DONOR ***
Posts: 9600
Joined: 18 Jun 2004 11:53 pm
Location: South Coast, UK

Re: REAR BUMPER REMOVAL???

Post by Chris_C » 26 May 2011 10:19 pm

Ah, ok, that's different to my towbar, that bolts to the same locations but still uses the bumper brackets :(
'89(G) 340 GLE B172k
'03 S60 D5 SE, '91 (J) MX5, 1954 Cyclemaster
Ex:
'89(F) 340 GL F7R (ex B172k) - Fake -> SBKV 300 Runner Up 08, 12; '91(H) 340 GL B14.4E - Kar; '88(F) 360 GLT B200E - Jet -> BKV 300 Runner Up 09; '89(G) 360 GLT B200E - Beast

Post Reply