Stripping a 480 Turbo Auto

B14, B172, B19/200, D16 engine, ignition, cooling, fuel & exhaust system, gearbox, variomatic, final drive... | Tuning: engine swaps, welded diff, clutch upgrades...
NO parts requests here, please use our V3M BUY & SELL corner
Post Reply
Rikochet
Posts: 11
Joined: 24 Nov 2014 08:56 pm

Stripping a 480 Turbo Auto

Post by Rikochet » 27 Nov 2014 07:35 pm

Hi everyone. Found this forum about 48 hours ago after stumbling across a post on Pistonheads about the humble Volvo 340 becoming very popular as a drift car.

Since then I mentioned the word Volvo to one mate, who said he thought another mate had some sort of Volvo turbo thing.

Long story short I'm picking up a low mileage Volvo 480 turbo tomorrow and will be taking it apart this weekend to get the parts I need to start building it into a 340 which I hope to purchase fairly soon.

Obvious issue is that it's an auto so I have a few questions.

1. What exactly do I need to remove from the 480 to be able to swap the engine over to a 340?

2. What other parts do I need to acquire from a manual car to make up for this being an auto?

3. What are the high value/rare/sought after items that I should keep from the 480 to sell on? I don't want it sitting on my driveway for longer than a few days and I'm not having people turning up with 20p for a heater switch! As long as I can make back what I spend on it I'll be happy and that can go towards getting a 340 :)

Ride_on
Posts: 2262
Joined: 26 May 2009 05:34 pm
Location: Belfast, N. Ireland

Re: Stripping a 480 Turbo Auto

Post by Ride_on » 27 Nov 2014 09:41 pm

The 480 is quite rare, probably more rare than 300 series. This is a 300 forum so not so many experts on 480s. Most 300 transplants come from Renaults (340) or 200/700/900 series volvos (360).

I think the 480 should fit straight in to a 340 with an extra pilot bearing possibly to link into the longer clutch shaft. I guess you will need a sump from a 1.7 340. Make sure the engine gearbox and diff mounts are in good condition. You may need to do something clever with injection system as the 340 fuel tank is not designed with a lift pump or in-tank pump.

The 480 engine guages are useful for the 340.
1980 345 DL_______1987 360 GLE (project car restored to GLT spec and B230FT'd)
1984 360 GLT______1987 360 GLT
1983 360 GLS______1989 360 GLE
1985 340 GL_______1986 340 1.4
1985 360 GLS______1995 940 SE 2.3 Turbo Estate (daily)
1987 340 GL 1.7

macplaxton
Posts: 3283
Joined: 09 Feb 2008 02:29 am

Re: Stripping a 480 Turbo Auto

Post by macplaxton » 28 Nov 2014 01:54 am

Someone was asking me about rear light clusters a few months back. They weren't desperate, just looking for a spare set, so keep them aside.
72 DAF 44 Estate 78 Volvo 343DL Black BeautyImageImage
82 Volvo 343DL CVTImageImage 88 Volvo 340DL Diesel

volvomania
Posts: 641
Joined: 09 Aug 2005 02:24 pm
Location: Antwerp, Belgium

Re: Stripping a 480 Turbo Auto

Post by volvomania » 28 Nov 2014 08:46 am

It is a shame to scrap a good 480 as these are getting rare quickly.
But what:
-Is the interior like, especially the front passenger seat?
-Are the pop-ups like?
Life is a journey, so sit back and enjoy the ride!

Born Built Beauties: Parts keeping our cars on the road!

http://www.Born-Built-Beauties.eu

Rikochet
Posts: 11
Joined: 24 Nov 2014 08:56 pm

Re: Stripping a 480 Turbo Auto

Post by Rikochet » 28 Nov 2014 09:12 am

volvomania wrote:It is a shame to scrap a good 480 as these are getting rare quickly.
But what:
-Is the interior like, especially the front passenger seat?
-Are the pop-ups like?
macplaxton wrote:Someone was asking me about rear light clusters a few months back. They weren't desperate, just looking for a spare set, so keep them aside.
The pop ups and the rear light clusters are 2 things I've found to be sought after. I'm picking up the car tonight so I'll have a look at those and the interior and get back to you both.

Rikochet
Posts: 11
Joined: 24 Nov 2014 08:56 pm

Re: Stripping a 480 Turbo Auto

Post by Rikochet » 28 Nov 2014 09:14 am

Ride_on wrote:The 480 is quite rare, probably more rare than 300 series. This is a 300 forum so not so many experts on 480s. Most 300 transplants come from Renaults (340) or 200/700/900 series volvos (360).

I think the 480 should fit straight in to a 340 with an extra pilot bearing possibly to link into the longer clutch shaft. I guess you will need a sump from a 1.7 340. Make sure the engine gearbox and diff mounts are in good condition. You may need to do something clever with injection system as the 340 fuel tank is not designed with a lift pump or in-tank pump.

The 480 engine guages are useful for the 340.
Will I also need to use the ECU and flywheel from a manual 1.7 turbo?

User avatar
Chris_C
*** V3M DONOR ***
Posts: 9600
Joined: 18 Jun 2004 11:53 pm
Location: South Coast, UK

Re: Stripping a 480 Turbo Auto

Post by Chris_C » 28 Nov 2014 02:18 pm

You will need the pilot bearing (all 400 engines would) and yes, you need the flywheel. Flywheel is specific to the 4x0 turbo (60-2 trigger pattern vs 22-2-22-2) and even of the turbos there are two types for the two clutch sizes. With a separate trigger wheel you could widen your search but I'd want to go for the engineered solution.

I'm not a 400 expert, but last time I looked the key tricky parts to get were seatbelt arms, any dash that isn't cracked somewhere, non faded rear lights, roller parcel shelves and clips etc.
'89(G) 340 GLE B172k
'03 S60 D5 SE, '91 (J) MX5, 1954 Cyclemaster
Ex:
'89(F) 340 GL F7R (ex B172k) - Fake -> SBKV 300 Runner Up 08, 12; '91(H) 340 GL B14.4E - Kar; '88(F) 360 GLT B200E - Jet -> BKV 300 Runner Up 09; '89(G) 360 GLT B200E - Beast

Rikochet
Posts: 11
Joined: 24 Nov 2014 08:56 pm

Re: Stripping a 480 Turbo Auto

Post by Rikochet » 28 Nov 2014 03:10 pm

Chris_C wrote:You will need the pilot bearing (all 400 engines would) and yes, you need the flywheel. Flywheel is specific to the 4x0 turbo (60-2 trigger pattern vs 22-2-22-2) and even of the turbos there are two types for the two clutch sizes. With a separate trigger wheel you could widen your search but I'd want to go for the engineered solution.

I'm not a 400 expert, but last time I looked the key tricky parts to get were seatbelt arms, any dash that isn't cracked somewhere, non faded rear lights, roller parcel shelves and clips etc.
Ok thanks but which car should I get the pilot bearing and flywheel from? Is it the 440/480 manual? I've been trying for the past couple of days to get onto the 480 forum but I've had no joy.

Ride_on
Posts: 2262
Joined: 26 May 2009 05:34 pm
Location: Belfast, N. Ireland

Re: Stripping a 480 Turbo Auto

Post by Ride_on » 28 Nov 2014 09:27 pm

The pilot should probably be from a rwd car, eg a 1.7 340, usually these are fairly standard things.

The flywheel needs to be from a manual car with the same ignition system, or you can use any manual flywheel from same series of engine if you make a triggerwheel for the ignition system you have.

It might be possible to bodge a less engineered solution using a renix ignition system from a 340 or perhaps a bosch from a 940 turbo. There are various maps available for 300s and 940 is a little programmable.
1980 345 DL_______1987 360 GLE (project car restored to GLT spec and B230FT'd)
1984 360 GLT______1987 360 GLT
1983 360 GLS______1989 360 GLE
1985 340 GL_______1986 340 1.4
1985 360 GLS______1995 940 SE 2.3 Turbo Estate (daily)
1987 340 GL 1.7

Post Reply