f7r\p backwards manifold
f7r\p backwards manifold
going bike carbs so not needed, done to a very high standard,
140ono item in chatham kent pick up ideally 07936384390 jake-
140ono item in chatham kent pick up ideally 07936384390 jake-
Re: f7r\p backwards manifold
must be abit pricey? 120ono...
Re: f7r\p backwards manifold
Got a picture? Cut and welded on the flange or cut the end off one side and put it on the other?
'89(G) 340 GLE B172k
'03 S60 D5 SE, '91 (J) MX5, 1954 Cyclemaster
Ex:
'89(F) 340 GL F7R (ex B172k) - Fake -> SBKV 300 Runner Up 08, 12; '91(H) 340 GL B14.4E - Kar; '88(F) 360 GLT B200E - Jet -> BKV 300 Runner Up 09; '89(G) 360 GLT B200E - Beast
'03 S60 D5 SE, '91 (J) MX5, 1954 Cyclemaster
Ex:
'89(F) 340 GL F7R (ex B172k) - Fake -> SBKV 300 Runner Up 08, 12; '91(H) 340 GL B14.4E - Kar; '88(F) 360 GLT B200E - Jet -> BKV 300 Runner Up 09; '89(G) 360 GLT B200E - Beast
Re: f7r\p backwards manifold
Yeah how well has it been done? I'm sure speedys manifold was the problem of his running
C25 ECV-1985-Mk2 340GL-Kessy
A889 VUY-1983-Mk2 360GLS-RUF
A889 VUY-1983-Mk2 360GLS-RUF
volvosneverdie wrote:Vnd says:
diffs, are like pubs and legs.
Best appreciated when open.
I probably should have specified ladies legs in there too. [+=] "embarrarrased emoticon"[].com
Re: f7r\p backwards manifold
Nah my running problem was due to a loom problem with the intake temp sensor. Adam swore by the design, not to mention he had it running perfectly for years before it went into my car.
Re: f7r\p backwards manifold
The welds look like been done by a pro .
Re: f7r\p backwards manifold
Will get pic asap. But it no messabout. The welds are perfect !
-
- *** V3M DONOR ***
- Posts: 2693
- Joined: 12 Sep 2006 09:07 pm
- Location: Sunderland, Ringpiece Of England
Re: f7r\p backwards manifold
I don't think people are asking about the quality of the welds, I think they're asking where on the manifold they are, four of them on the inlet runners or one big one after the throttle body?
'87 Nissan Sunny
'95 945 LPT
'90 340 3dr
'87 360 GLT
'87 765 TIC
'75 Manta A
'70 Rover P5 V8
'67 MGB GT
'62 amazon 2dr
'95 945 LPT
'90 340 3dr
'87 360 GLT
'87 765 TIC
'75 Manta A
'70 Rover P5 V8
'67 MGB GT
'62 amazon 2dr
Re: f7r\p backwards manifold
Much better put than I managed!filthyjohn wrote:I don't think people are asking about the quality of the welds, I think they're asking where on the manifold they are, four of them on the inlet runners or one big one after the throttle body?
'89(G) 340 GLE B172k
'03 S60 D5 SE, '91 (J) MX5, 1954 Cyclemaster
Ex:
'89(F) 340 GL F7R (ex B172k) - Fake -> SBKV 300 Runner Up 08, 12; '91(H) 340 GL B14.4E - Kar; '88(F) 360 GLT B200E - Jet -> BKV 300 Runner Up 09; '89(G) 360 GLT B200E - Beast
'03 S60 D5 SE, '91 (J) MX5, 1954 Cyclemaster
Ex:
'89(F) 340 GL F7R (ex B172k) - Fake -> SBKV 300 Runner Up 08, 12; '91(H) 340 GL B14.4E - Kar; '88(F) 360 GLT B200E - Jet -> BKV 300 Runner Up 09; '89(G) 360 GLT B200E - Beast
-
- *** V3M DONOR ***
- Posts: 5461
- Joined: 25 Apr 2005 06:52 pm
- Location: Anglesey North Wales
- Contact:
Re: f7r\p backwards manifold
From memory I think the manifolds Adam had done were with the throttle plate cut and welded onto other end rather the cut on the runners.
Dai
Please email me directly on dai@classicswede.co.uk
http://www.classicswede.com
phone/text 07824887160
Web shop http://www.classicswede.co.uk/
Please email me directly on dai@classicswede.co.uk
http://www.classicswede.com
phone/text 07824887160
Web shop http://www.classicswede.co.uk/
Re: f7r\p backwards manifold
That how this one has been done