B230ET/FT bits

Put here your advertisements to sell cars and parts
Post Reply
User avatar
thododd
Posts: 303
Joined: 22 Jul 2012 09:58 pm
Location: Gloucester/ Bristol

B230ET/FT bits

Post by thododd » 07 Oct 2014 06:52 pm

ive been gathering some engine bits lately and i forgot to stop at enough ... ive got 1 full engine, a extra complete bottom end, a pair of inlet manifolds and a futher set of pistons w/ rods. so surpluss atm are;

9mm B230ET conrods
B230FT low comp pistons
1x complete inlet manifold
oil filter arm
a pair of 940 engine mounts
940 B230FT sump
crank pulleys, cambelt covers etc etc

if anyone is need of rods or pistons (ie after melting/destroying some, being juvenile) and they ask nicely, i could be pursuaded to donate them for a cause.... but ideally id like £75 for the lot.

postage available or collect from Bristol/Stroud

Thanks
Tom

User avatar
filthyjohn
*** V3M DONOR ***
Posts: 2693
Joined: 12 Sep 2006 09:07 pm
Location: Sunderland, Ringpiece Of England

Re: B230ET/FT bits

Post by filthyjohn » 19 Oct 2014 09:38 pm

You don't have a B230FT/FK flywheel do you? The 'dogdish' type? Could collect as I'll be in the bristol area in a week or so.
'87 Nissan Sunny
'95 945 LPT
'90 340 3dr
'87 360 GLT
'87 765 TIC
'75 Manta A
'70 Rover P5 V8
'67 MGB GT
'62 amazon 2dr

User avatar
thododd
Posts: 303
Joined: 22 Jul 2012 09:58 pm
Location: Gloucester/ Bristol

Re: B230ET/FT bits

Post by thododd » 20 Oct 2014 05:59 pm

i do have 1, but its for my engine build. sorry

bristol is quite far from home, isnt it? what brings you to the west country?

User avatar
filthyjohn
*** V3M DONOR ***
Posts: 2693
Joined: 12 Sep 2006 09:07 pm
Location: Sunderland, Ringpiece Of England

Re: B230ET/FT bits

Post by filthyjohn » 21 Oct 2014 12:17 am

Family birthday party mate, a joint function for my cousin and her daughter, for which I need a hallowe'en themed costume :roll:
'87 Nissan Sunny
'95 945 LPT
'90 340 3dr
'87 360 GLT
'87 765 TIC
'75 Manta A
'70 Rover P5 V8
'67 MGB GT
'62 amazon 2dr

Ride_on
Posts: 2262
Joined: 26 May 2009 05:34 pm
Location: Belfast, N. Ireland

Re: B230ET/FT bits

Post by Ride_on » 22 Oct 2014 10:58 pm

You can you use the 360 flywheel if you do something different with the ignition. I even think the right renix would work well.
1980 345 DL_______1987 360 GLE (project car restored to GLT spec and B230FT'd)
1984 360 GLT______1987 360 GLT
1983 360 GLS______1989 360 GLE
1985 340 GL_______1986 340 1.4
1985 360 GLS______1995 940 SE 2.3 Turbo Estate (daily)
1987 340 GL 1.7

User avatar
filthyjohn
*** V3M DONOR ***
Posts: 2693
Joined: 12 Sep 2006 09:07 pm
Location: Sunderland, Ringpiece Of England

Re: B230ET/FT bits

Post by filthyjohn » 23 Oct 2014 08:53 pm

^^^ I'm probably going to use a trigger wheel at this rate. I have a nice lightened flywheel I can use.
'87 Nissan Sunny
'95 945 LPT
'90 340 3dr
'87 360 GLT
'87 765 TIC
'75 Manta A
'70 Rover P5 V8
'67 MGB GT
'62 amazon 2dr

Post Reply