German 360 (16v project)
Re: German 360 (16v project)
ehm i just went to the garage to check this and there's def no offset boltpattern. as james said, bolts will fit in every postion.
so i still have no clue how to mount it right
i'm just searching the net but still no info yet.
so i still have no clue how to mount it right
i'm just searching the net but still no info yet.
Sideways @ flat 2 the mat forever!
Rally-gious!
Rally-gious!
-
- Posts: 1921
- Joined: 06 Dec 2008 09:35 pm
- Location: Netherlands.
- Contact:
Re: German 360 (16v project)
haha, cool & weird! my memory wasn't as good as i thought then! sorry cutler & thx foggyjames!
i did aswell mention this for mounting, so no need searching the netvolvodspec wrote:in case you're in doubt, put cyl 1 on top dead center, and then put the marking on the flywheel straight up
Re: German 360 (16v project)
ok, found this:
http://forums.turbobricks.com/showthrea ... t=flywheel
http://forums.turbobricks.com/showthrea ... t=flywheel
http://forums.turbobricks.com/showthrea ... t=flywheel
http://www.brickboard.com/FAQ/700-900/E ... stallation
http://forums.turbobricks.com/showpost. ... stcount=27
http://forums.turbobricks.com/showthread.php?t=7128
that should do the trick
http://forums.turbobricks.com/showthrea ... t=flywheel
http://forums.turbobricks.com/showthrea ... t=flywheel
http://forums.turbobricks.com/showthrea ... t=flywheel
http://www.brickboard.com/FAQ/700-900/E ... stallation
http://forums.turbobricks.com/showpost. ... stcount=27
http://forums.turbobricks.com/showthread.php?t=7128
that should do the trick
in the last link above it saysand then put the marking on the flywheel straight up
however, if i use all tricks at once i should get it spot on...at least i hope so^^Later flywheels which have a lightly etched arrow, the arrow should be horizontal and pointing to the right.
Sideways @ flat 2 the mat forever!
Rally-gious!
Rally-gious!
-
- Posts: 1921
- Joined: 06 Dec 2008 09:35 pm
- Location: Netherlands.
- Contact:
Re: German 360 (16v project)
woops, delete that! just spoke to guy who just swapped his b200 to a b230 and he sayd this:
get cyl1 to TDC
on the flywheel there is a black marking, put this marking (seen from the rear of the engine) at 15:15hour (to the right)
then bolt holes should perfectly line up + timing ok
get cyl1 to TDC
on the flywheel there is a black marking, put this marking (seen from the rear of the engine) at 15:15hour (to the right)
then bolt holes should perfectly line up + timing ok
-
- *** V3M DONOR ***
- Posts: 9361
- Joined: 29 Jan 2004 04:20 am
- Location: Nottingham, UK
Re: German 360 (16v project)
The LH2.4 flywheels line up at "45 minutes past", and I had a feeling Renix was the opposite...so that makes sense
It's a shame I don't have a Renix car here to check
cheers
James
It's a shame I don't have a Renix car here to check
cheers
James
VOC 300-series Register Keeper
'89 740 Turbo Intercooler
'88 360 Turbo Intercooler
'85 360 GLT
'81 343 GLS R-Sport
'79 343 DL
'70 164
...and some modern FWD nonsense to get me to work...
'89 740 Turbo Intercooler
'88 360 Turbo Intercooler
'85 360 GLT
'81 343 GLS R-Sport
'79 343 DL
'70 164
...and some modern FWD nonsense to get me to work...
Re: German 360 (16v project)
Sideways @ flat 2 the mat forever!
Rally-gious!
Rally-gious!
Re: German 360 (16v project)
Sideways @ flat 2 the mat forever!
Rally-gious!
Rally-gious!
Re: German 360 (16v project)
engine is in and car back on its feet.
now i'll work on the carbs and the heater box.
i need to order suspension stuff from dai as well but no clue whats going in with his front shocks.
now i'll work on the carbs and the heater box.
i need to order suspension stuff from dai as well but no clue whats going in with his front shocks.
Sideways @ flat 2 the mat forever!
Rally-gious!
Rally-gious!
Re: German 360 (16v project)
carbs are cleaned, it was def nessacary. main jets are 145 at the outside and 150 at the inside in the stock setup. drilled them out to 200 on all four carbs. i expect massiv fiddeling anyways so its just a starting point.
Sideways @ flat 2 the mat forever!
Rally-gious!
Rally-gious!
Re: German 360 (16v project)
another problem came up: i can't get a single water pump gasket from the dealer, only with a new pump and mine is still good.
will hylomar do the trick instead of the original gasket?
will hylomar do the trick instead of the original gasket?
Sideways @ flat 2 the mat forever!
Rally-gious!
Rally-gious!
-
- *** V3M DONOR ***
- Posts: 9361
- Joined: 29 Jan 2004 04:20 am
- Location: Nottingham, UK
Re: German 360 (16v project)
If the waterpump is the same as for a 8v (not sure...), you can get them from other parts stores. I know Euro Car Parts here in the UK do them for 8v.
cheers
James
cheers
James
VOC 300-series Register Keeper
'89 740 Turbo Intercooler
'88 360 Turbo Intercooler
'85 360 GLT
'81 343 GLS R-Sport
'79 343 DL
'70 164
...and some modern FWD nonsense to get me to work...
'89 740 Turbo Intercooler
'88 360 Turbo Intercooler
'85 360 GLT
'81 343 GLS R-Sport
'79 343 DL
'70 164
...and some modern FWD nonsense to get me to work...
Re: German 360 (16v project)
i'll just slide that in here:
on sale in ger for a while now. please some germans on here, safe that car!
http://www.autoscout24.de/Details.aspx?id=brvqkzqjigiv
it's to far away from me and i don't have space to store it!
on sale in ger for a while now. please some germans on here, safe that car!
http://www.autoscout24.de/Details.aspx?id=brvqkzqjigiv
it's to far away from me and i don't have space to store it!
Sideways @ flat 2 the mat forever!
Rally-gious!
Rally-gious!
-
- *** V3M DONOR ***
- Posts: 4398
- Joined: 06 Jan 2007 02:38 pm
- Location: Bonn, Germany
Re: German 360 (16v project)
It does look good, very low mileage too!
But:
wayyy down south in Munich
no special equipment (cat, PAS air con) to make it deserve that high price tag ...
Tom
But:
wayyy down south in Munich
no special equipment (cat, PAS air con) to make it deserve that high price tag ...
Tom
343 GL Touring B14.1E CVT (155) 98000kms 1980 (sold)
343 L Junior B14.3E MT4 (155) 229000kms 1981 (scrapped)
343 DLS B19A MT4 (155) 167900kms 1982
360 GL Injection B200F MT5 (231) 348598kms 1988 (scrapped)
360 GLT B200F MT5 (302) 230000kms 1988
343 L Junior B14.3E MT4 (155) 229000kms 1981 (scrapped)
343 DLS B19A MT4 (155) 167900kms 1982
360 GL Injection B200F MT5 (231) 348598kms 1988 (scrapped)
360 GLT B200F MT5 (302) 230000kms 1988
Re: German 360 (16v project)
yeah price is way off most of the time on these kinda selling boards.
but i'm perfectly sure you don't have to pay the price he offers...especially after he realizes that nobody wants the car anyways.
there was a 360 on ebay not to long ago, broken gearbox an pretty neat all around...someone bought it for 1€. was to far away for me as well, would have grabed it right away.
it's a shame that i've got very limited time on my hands in the recent months, can't work on my 360 and not check the net for good volvo cars as well...i'm sure some good offers have been missed. seems like good cars have shown up more frequently in the past year or so.
but i'm perfectly sure you don't have to pay the price he offers...especially after he realizes that nobody wants the car anyways.
there was a 360 on ebay not to long ago, broken gearbox an pretty neat all around...someone bought it for 1€. was to far away for me as well, would have grabed it right away.
it's a shame that i've got very limited time on my hands in the recent months, can't work on my 360 and not check the net for good volvo cars as well...i'm sure some good offers have been missed. seems like good cars have shown up more frequently in the past year or so.
Sideways @ flat 2 the mat forever!
Rally-gious!
Rally-gious!