1.4 to F7R conversion bits wanted

Put here your advertisements to buy cars and parts
Post Reply
User avatar
valman
Posts: 663
Joined: 07 Feb 2010 11:16 pm
Location: Bedfordshire

1.4 to F7R conversion bits wanted

Post by valman » 06 Jun 2012 10:43 am

basically need everything to put an f7r into a 1.4. i have copy and pasted the list below from the wiki for all the bits im after basically plus a few others, cheers

1.7 sump
1.7 bellhousing
1.7 clutch
1.7 clutch cable (although a 1.4 can be used with a bit of inginuety)
1.7 front engine mounts (Rhs 3 bolt bracket to block - Lhs 3 bolt bracket to sump)
1.7 LHS rear bellhousing mount (1.4 can be used with a little trimming to clear clutch fork)( have had no clearance issues-kaos)
1.7 alternator mounts
1.7 water pipes
1.7/1.4 water temp sender(not sure if i need this, can someone verify? thanks)

extra bits:
5 speed gearbox, preferably unwelded diff.
5 speed Prop, (good to have a spare)

thanks, if theres anything else i need please advise
Last edited by valman on 05 Jul 2012 02:53 pm, edited 3 times in total.
ImageImage

User avatar
valman
Posts: 663
Joined: 07 Feb 2010 11:16 pm
Location: Bedfordshire

Re: Starter motor for a 1.4

Post by valman » 09 Jun 2012 05:13 pm

bump
ImageImage

User avatar
valman
Posts: 663
Joined: 07 Feb 2010 11:16 pm
Location: Bedfordshire

Re: 1.4 (b14.4 engine long block) whole engine, w/e

Post by valman » 02 Jul 2012 03:38 pm

bump
ImageImage

Attack2001
Posts: 1015
Joined: 05 Jun 2011 03:45 pm
Location: Rochester, Kent
Contact:

Re: 1.4 (b14.4 engine long block) whole engine, w/e

Post by Attack2001 » 05 Jul 2012 12:47 pm

I didnt get a reply from that gezzer about the engine, sorry man :/
Image

User avatar
valman
Posts: 663
Joined: 07 Feb 2010 11:16 pm
Location: Bedfordshire

Re: 1.4 (b14.4 engine long block) whole engine, w/e

Post by valman » 05 Jul 2012 02:51 pm

no worries man, thanks anyway! plans changed a little
ImageImage

theo2468
Posts: 1417
Joined: 11 Oct 2010 02:34 am
Location: cornwall

Re: 1.4 to F7R conversion bits wanted

Post by theo2468 » 05 Jul 2012 05:27 pm

I've got a prop and some mounts, pm me
C25 ECV-1985-Mk2 340GL-Kessy
A889 VUY-1983-Mk2 360GLS-RUF
volvosneverdie wrote:Vnd says:
diffs, are like pubs and legs.
Best appreciated when open.
I probably should have specified ladies legs in there too. [+=] "embarrarrased emoticon"[].com

User avatar
quietman
Posts: 30
Joined: 18 Jun 2008 05:52 pm
Location: sunderland

Re: 1.4 to F7R conversion bits wanted

Post by quietman » 13 Jul 2012 03:06 pm

if you fancy a f7p i got everthing you need but the diff is welded

User avatar
valman
Posts: 663
Joined: 07 Feb 2010 11:16 pm
Location: Bedfordshire

Re: 1.4 to F7R conversion bits wanted

Post by valman » 13 Jul 2012 05:48 pm

quietman wrote:if you fancy a f7p i got everthing you need but the diff is welded
pm'd
ImageImage

Post Reply