Page 4 of 5

Re: An idea R.e FAQ Section

Posted: 25 Jan 2012 02:21 pm
by Chris_C
Bumping this to remind me, as I'd forgotten...

Re: An idea R.e FAQ Section

Posted: 25 Jan 2012 02:43 pm
by Attack2001
Would this guide be any use to the VOC/BKV thing? I mean printing it off, and having them as handouts etc for people to have a read up on the 300 series?

Re: An idea R.e FAQ Section

Posted: 28 Jan 2012 01:16 am
by Evoman
In side of a FAQ, how about a wiki, people can easily add stuff to it as and when questions come up, people can post guides to stuff they have done etc

btw, I have no clue how to set one up. I tried googling but there were too many acronyms, these were the type where the case changes in the middle :lol:

Re: An idea R.e FAQ Section

Posted: 28 Jan 2012 01:53 am
by macplaxton
Evoman wrote:In side of a FAQ, how about a wiki, people can easily add stuff to it as and when questions come up, people can post guides to stuff they have done etc

btw, I have no clue how to set one up. I tried googling but there were too many acronyms, these were the type where the case changes in the middle :lol:
I'll see what I can do. Been talking about it to a few folk, now is really time to stop talking and start doing something. :oops: Give me a month or so.

Re: An idea R.e FAQ Section

Posted: 28 Jan 2012 09:56 am
by Chris_C

Re: An idea R.e FAQ Section

Posted: 02 Mar 2012 08:56 pm
by Nimminz
Another one for the rare accessories section:

Cavity covers :D

Image

Image

Re: An idea R.e FAQ Section

Posted: 02 Mar 2012 09:29 pm
by Speedy88
Can we please add this to the main FAQ? I don't think many people knew this until I found out through Jani:

Can you use a 360 box in a 340 and vice-versa?
Yes, if it's a 5-speed. But you'll need to swap over two main parts.

Firstly, the front plates should be taken off to be mounted on the front of your new gearbox. This is because the torque tube (360) and prop shaft (340) have completely different arrangements of connecting.

Secondly you'll need to swap the front shafts over. 360 and 340 boxes use different shafts with completely different spline arrangements. All you need to do is remove the front shaft and gear as seen just to the left of this gearbox:

Image

They are held in with a circlip (thanks again jani :D ). All you need to do is insert that into your new box and bolt your new front plate on. Jobs a goodun!

Re: An idea R.e FAQ Section

Posted: 02 Mar 2012 09:52 pm
by Attack2001
There we go, both bits added :) Even though the wiki is being put together, i wonder whether this would be useful as a PDF? Something that can be printed off instead of having to keep checking on here? Thomas...................

Re: An idea R.e FAQ Section

Posted: 02 Mar 2012 09:57 pm
by Evoman
^thats good thinking! maybe all guides could be in pdf format

Re: An idea R.e FAQ Section

Posted: 02 Mar 2012 10:17 pm
by Speedy88
It's a good idea but bear in mind that perhaps most of the information should be collected first, otherwise you'll have multiple versions of the document floating around every time this is updated.

Re: An idea R.e FAQ Section

Posted: 02 Mar 2012 10:19 pm
by Attack2001
Speedy88 wrote:It's a good idea but bear in mind that perhaps most of the information should be collected first, otherwise you'll have multiple versions of the document floating around every time this is updated.
Yup i was thinking the same thing, so maybe not straight away, but if it keeps going then its a possibility :)

Re: An idea R.e FAQ Section

Posted: 02 Mar 2012 11:08 pm
by macplaxton
Attack2001 wrote:I wonder whether this would be useful as a PDF? Something that can be printed off instead of having to keep checking on here?
Evoman wrote:^thats good thinking! maybe all guides could be in pdf format
Nah, what's wrong with going to the Wiki, under heading "Toolbox" on the left and clicking "Printable version" and just printing it off if you need it. :wink:

PDF? Pffft! Whatever next? Are youse lot going to be asking for stuff in MS Word Document format? :roll: :P sm6

Re: An idea R.e FAQ Section

Posted: 02 Mar 2012 11:11 pm
by Attack2001
macplaxton wrote:
Attack2001 wrote:I wonder whether this would be useful as a PDF? Something that can be printed off instead of having to keep checking on here?
Evoman wrote:^thats good thinking! maybe all guides could be in pdf format
Nah, what's wrong with going to the Wiki, under heading "Toolbox" on the left and clicking "Printable version" and just printing it off if you need it. :wink:

PDF? Pffft! Whatever next? Are youse lot going to be asking for stuff in MS Word Document format? :roll: :P sm6
Bust out the windows 95 and the inkjet printer!! :lol: :lol:

Re: An idea R.e FAQ Section

Posted: 02 Mar 2012 11:24 pm
by macplaxton
Well if your really have to have a PDF, select printable version on the wiki, and print it to a PDF file, instead of paper? :?

Re: An idea R.e FAQ Section

Posted: 03 Mar 2012 11:10 pm
by Speedy88
Sorry, another one! Hope this is of some use to people, especially us youngsters with our choons:

Ever wanted to make your radio work without the ignition on? Cut this green wire here:
Image

Simply run it to the 2 lives here, offline and online positives (yellow and red)
Image

Happy days!
Image