Big ends for '86 B200E

Post by **pettaw** » 29 Jan 2005 03:42 pm

Mine only uses a very little oil, but I don't know the history of the car.

From the look of it, the way the driver's seat is ripped, and all the engine covers etc were on with twisties or cable clips and half the electrics weren't working I'd say it had a hard life.

Like you say there's no rush, but I reckon I'm gonna do it in the summer time, and if I install a scrappy engine in the car, it keeps it going and gives me time to research and do the work properly.

Post by **foggyjames** » 29 Jan 2005 04:18 pm

pettaw wrote:all the engine covers etc were on with twisties or cable clips

Haha - class! Good luck with it - let me know if you want a hand sourcing an engine.

cheers

James

Post by **pettaw** » 29 Jan 2005 05:08 pm

thanks, I really want to do it to OEM, so that means dealer parts, if they still make them. I really wish there was a way of checking parts availability on the net without having to march into the dealer with a load of numbers and wait for them to disappear into the back room.

Post by **foggyjames** » 29 Jan 2005 06:15 pm

I can't see parts being unavailable - for example as far as I'm aware the big end bearings will be the same ones to be found in a B230 from 1998.

cheers

James

Post by **pettaw** » 31 Jan 2005 03:42 pm

right, I phoned the dealer and everything is still available, gaskets, rings pistons, valves, bearings etc.

Apart from the oil pump, but the oil pressure light seems to go off OK so hopefully that should be OK, if the spring's short I might be able to get a machine shop to remake one for me.

I phoned up Braydon who have a B200E in stock but the price tag is 170, which seems a bit steep, so any ideas sourcing an engine- doesn't have to be in great condition, as long as it runs OKish to get me by whilst I rebuild my lump- would be appreciated.

I've got the B19/B200 engine green book, so that should cover everything.

Post by **foggyjames** » 31 Jan 2005 08:23 pm

I'll ask around, but £50 isn't out of the question...

cheers

James

Post by **petefarrell360** » 31 Jan 2005 11:39 pm

Hi there Pettaw, I may be able to help you with sourcing an engine! It is currently in an 86 D 360 GLT, a crashed car, side impact, so engine bay is untouched, low mileage engine. It hasn't run for a while, but I have heard and seen it running, and it did sound fine back then. If you're interested please let me know, email is at the bottom of my post. Where abouts are you? Pete

Post by **pettaw** » 01 Feb 2005 11:13 am

Pete, thanks for the offer.

I'm in Wembley, but I don't really have any means of ferreting an engine around. I'm interested if you've got some way of getting it to my house.

Post by **foggyjames** » 01 Feb 2005 12:49 pm

You'd get a longblock minus manifolds into the boot of your car! Easily into a hatch. Lifting it might be fun mind you (speaks the voice of recent experience

)...

cheers

James

Post by **wjp01908** » 01 Feb 2005 04:52 pm

Should be fine in your car pettaw.

Get some blokes round and it should be OK lifting it too (I`d be happy to lend a hand as I`m not far from Pete)

Getting out of the car when you get it home may be more problematic though unless you have a particularly amazonian wife/girlfriend.

Will

Post by **pettaw** » 01 Feb 2005 06:00 pm

That'll be fine, cos I've got, me, my brother, my Dad and my Mum, and hopefully if it arrives in time, an engine hoist from Screwfix, if it comes to that.

I was just worried about getting it in the boot, the saloons aren't quite as useful in that regard as the hatchbacks, which, frankly have just as much room as some estates.

Post by **petefarrell360** » 01 Feb 2005 07:27 pm

Hi again, well as it is currently still in the car, which is in the process of being striped of parts before it leaves me. This means it will, soon, be just a bare shell. So should you be interested, you could then have an axle, gearbox and basic running gear along with the engine, this would certainly make transportation a lot easier, as it will still be on wheels! This way it could be loaded onto a trailer. The saloons are nice in my opinion, although load space is rather restricted and a bit unusable compared to a hatchback. Let me know if you'd prefer the option I've suggested which makes transportation easier!
Pete

Post by **pettaw** » 01 Feb 2005 07:53 pm

I think just the engine would be great thanks, I've already got another g/box rusting in the back garden I don't know what to do with

It needs a rebuild because the gears were a bit crunchy....

I could do with a torque tube though, provided the end float isn't too great.

Oh, and I hope a 1987 engine will work in a 1986 car with the wiring loom etc. I reckon I'll need the Renix control unit though, for sure.

Post by **petefarrell360** » 01 Feb 2005 07:59 pm

Ok, well, I'd imagine the wiring loom is the same, no real changes, as it's still the same model, after the facelift. If you can remove the engine, that would be best, I can help with this however and loading. It's also very good of Will to offer his services too.
Pete

Post by **foggyjames** » 01 Feb 2005 08:02 pm

Save me a complete drivetrain for when I have the space to store it

cheers

James