B19 VS B200

B14, B172, B19/200, D16 engine, ignition, cooling, fuel & exhaust system, gearbox, variomatic, final drive... | Tuning: engine swaps, welded diff, clutch upgrades...
NO parts requests here, please use our V3M BUY & SELL corner
User avatar
mrborrie
Posts: 240
Joined: 06 Jul 2010 08:17 am
Location: Netherlands

B19 VS B200

Post by mrborrie » 03 Feb 2011 07:10 pm

What are the diffrences between the 2 engines? Could i swap over B200 injection on a B19 or will i lose some power over the 1,0?
764 Turbo 86'|Volvo 144 72|Volvo 360 86'||Volvo 360 GLS 85'|242 77"|
Website: http://www.brick-autosport.com
Facebook: http://www.facebook.com/pages/Brick-Aut ... 98?sk=wall"

Ride_on
Posts: 2262
Joined: 26 May 2009 05:34 pm
Location: Belfast, N. Ireland

Re: B19 VS B200

Post by Ride_on » 06 Feb 2011 11:42 pm

No difference in the injection system AFAIK. The B200 is a low friction version of the B19.
1980 345 DL_______1987 360 GLE (project car restored to GLT spec and B230FT'd)
1984 360 GLT______1987 360 GLT
1983 360 GLS______1989 360 GLE
1985 340 GL_______1986 340 1.4
1985 360 GLS______1995 940 SE 2.3 Turbo Estate (daily)
1987 340 GL 1.7

User avatar
mrborrie
Posts: 240
Joined: 06 Jul 2010 08:17 am
Location: Netherlands

Re: B19 VS B200

Post by mrborrie » 07 Feb 2011 12:57 pm

Thing it i got a parts car with injection and a 85 GLS with carb.
I was thinking of swapping all the bits over. i hoped the loom for the injection was separate from the headlights and horn etc but its not.
Swapping just the entire loom + relaybox from the enginecompartment and the bit that goes to the ECU would be enough to convert to injection or am i missing something crusial.
764 Turbo 86'|Volvo 144 72|Volvo 360 86'||Volvo 360 GLS 85'|242 77"|
Website: http://www.brick-autosport.com
Facebook: http://www.facebook.com/pages/Brick-Aut ... 98?sk=wall"

Ride_on
Posts: 2262
Joined: 26 May 2009 05:34 pm
Location: Belfast, N. Ireland

Re: B19 VS B200

Post by Ride_on » 07 Feb 2011 04:24 pm

Mostly. There maybe some differences in the head. For instance I think the B200K uses water heating in the manifold and you have to block these ports up to convert to injection. Also check the holes for the cold start switch and idle bypass valve.
1980 345 DL_______1987 360 GLE (project car restored to GLT spec and B230FT'd)
1984 360 GLT______1987 360 GLT
1983 360 GLS______1989 360 GLE
1985 340 GL_______1986 340 1.4
1985 360 GLS______1995 940 SE 2.3 Turbo Estate (daily)
1987 340 GL 1.7

User avatar
volvodspec
Posts: 1921
Joined: 06 Dec 2008 09:35 pm
Location: Netherlands.
Contact:

Re: B19 VS B200

Post by volvodspec » 07 Feb 2011 05:12 pm

i bet the B19 has a lazier cam and maybe even slightly lower CR as the B200

everything should fysically fit though, but i'd personally swap the complete engine; less work!

User avatar
mrborrie
Posts: 240
Joined: 06 Jul 2010 08:17 am
Location: Netherlands

Re: B19 VS B200

Post by mrborrie » 08 Feb 2011 10:58 am

Yeah im now pretty sure i will swap the entire thing.
Just wondering about the loom in the injected car, the headlights etc are worked into it too but it all goes to that fuse/relay box and one bit into the car thats connected to the ECU.
If i swap over all that stuff it should have all the bits i need to do the swap and have a functional injection system or are there fuses somewhere in the dash i will need too?
764 Turbo 86'|Volvo 144 72|Volvo 360 86'||Volvo 360 GLS 85'|242 77"|
Website: http://www.brick-autosport.com
Facebook: http://www.facebook.com/pages/Brick-Aut ... 98?sk=wall"

User avatar
volvodspec
Posts: 1921
Joined: 06 Dec 2008 09:35 pm
Location: Netherlands.
Contact:

Re: B19 VS B200

Post by volvodspec » 08 Feb 2011 04:52 pm

injection loom is separate from the normal engine-bay loom (with the headlights, wiper motor etc)

User avatar
mrborrie
Posts: 240
Joined: 06 Jul 2010 08:17 am
Location: Netherlands

Re: B19 VS B200

Post by mrborrie » 08 Feb 2011 06:53 pm

Sweet that's a load of my mind!
EDIT: Still i had the feeling it was joined at some points, i'll take a few pics of it
764 Turbo 86'|Volvo 144 72|Volvo 360 86'||Volvo 360 GLS 85'|242 77"|
Website: http://www.brick-autosport.com
Facebook: http://www.facebook.com/pages/Brick-Aut ... 98?sk=wall"

Ride_on
Posts: 2262
Joined: 26 May 2009 05:34 pm
Location: Belfast, N. Ireland

Re: B19 VS B200

Post by Ride_on » 10 Feb 2011 01:33 am

I pulled out a B200E injection loom pretty easily so I think its not connected.

Compression ration from 1982 B19 in 360s is 10:1 same as B200s. However an 85 GLS should be a B200K (well mine was), does it have the Stromberg variable jet side draught carb?
1980 345 DL_______1987 360 GLE (project car restored to GLT spec and B230FT'd)
1984 360 GLT______1987 360 GLT
1983 360 GLS______1989 360 GLE
1985 340 GL_______1986 340 1.4
1985 360 GLS______1995 940 SE 2.3 Turbo Estate (daily)
1987 340 GL 1.7

User avatar
mrborrie
Posts: 240
Joined: 06 Jul 2010 08:17 am
Location: Netherlands

Re: B19 VS B200

Post by mrborrie » 10 Feb 2011 01:53 pm

no it has the solex one but its busted
764 Turbo 86'|Volvo 144 72|Volvo 360 86'||Volvo 360 GLS 85'|242 77"|
Website: http://www.brick-autosport.com
Facebook: http://www.facebook.com/pages/Brick-Aut ... 98?sk=wall"

User avatar
Fuse
Posts: 1364
Joined: 29 Jul 2004 09:03 pm
Location: Finland
Contact:

Re: B19 VS B200

Post by Fuse » 10 Feb 2011 05:01 pm

Injection harness is separate. Here's a pic of LU-Jetronic's harness.

Image
Volvo R-Sport - Equipment for the car enthusiast.

“Buy land, they're not making it anymore” - Mark Twain


"There are only three sports: bullfighting, motor racing, and mountaineering; all the rest are merely games." -Ernest Hemingway

User avatar
mrborrie
Posts: 240
Joined: 06 Jul 2010 08:17 am
Location: Netherlands

Re: B19 VS B200

Post by mrborrie » 10 Feb 2011 10:04 pm

Hmmmm interesting! i'm sure mine where hooked up on some points lemme get some pics of that tomorrow.
764 Turbo 86'|Volvo 144 72|Volvo 360 86'||Volvo 360 GLS 85'|242 77"|
Website: http://www.brick-autosport.com
Facebook: http://www.facebook.com/pages/Brick-Aut ... 98?sk=wall"

User avatar
volvodspec
Posts: 1921
Joined: 06 Dec 2008 09:35 pm
Location: Netherlands.
Contact:

Re: B19 VS B200

Post by volvodspec » 10 Feb 2011 10:11 pm

engine side the only things hooked to the normal loom are starter motor, alternator, coolant temp sender and oil pressure sender

Ride_on
Posts: 2262
Joined: 26 May 2009 05:34 pm
Location: Belfast, N. Ireland

Re: B19 VS B200

Post by Ride_on » 12 Feb 2011 12:34 am

Solex downdraft would be a B200K, unless its a mix and match engine swap already. Why do you think its a B19? The number is usually only on the timing belt cover, its possible it says B19 on the block, but thats misleading.

You will defo need to put in some core plugs into the head to convert a B200K to injection, not a difficult or expensive job AFAIK, but I've never done it.
1980 345 DL_______1987 360 GLE (project car restored to GLT spec and B230FT'd)
1984 360 GLT______1987 360 GLT
1983 360 GLS______1989 360 GLE
1985 340 GL_______1986 340 1.4
1985 360 GLS______1995 940 SE 2.3 Turbo Estate (daily)
1987 340 GL 1.7

User avatar
mrborrie
Posts: 240
Joined: 06 Jul 2010 08:17 am
Location: Netherlands

Re: B19 VS B200

Post by mrborrie » 13 Feb 2011 12:43 pm

these are the 2 wires the injectionloom is wired to the other loom,
That other looms also has a connector that goes into the bendix coil.. will that present on the carbloom ?

Image
764 Turbo 86'|Volvo 144 72|Volvo 360 86'||Volvo 360 GLS 85'|242 77"|
Website: http://www.brick-autosport.com
Facebook: http://www.facebook.com/pages/Brick-Aut ... 98?sk=wall"

Post Reply