20mm and 25mm spacers still for sale ?

Take it you don't have the bolts or shallow nuts.

Hello. Looking for some help I have a full loom pre cut and made by Yourself for my clio conversion but I am really crap at wiring even though it's labeled. Do you have step by step photos of the join I need onto factory loom I stopped working on my car 2 years ago as the wiring scared me and I have...

Hello. Looking for some help I have a full loom pre cut and made by Adam for my clio conversion but I am really crap at wiring even though it's labeled. Looking for someone in the know to help me wire it and get it running. I am happy to PayPal them some money if they can do it over the phone for he...

Hello. I currently have a few interested in the front coilovers at £400 Interest in engine with loom and bell housing ect for £500 Interest in rear coilovers at £500 Wheels would be £300. They have 5 brand new tyres. If anyone wants parts I am going to try and get this moving along as I think its ti...

Hi, I would be very interested in a few bits, I'm currently building a 340 and doing the F7P conversion, but I am working with blocks and shocks with diff oil in them at the min so I would be very interested in the 5 link kit and coil overs front and back, and alley tank etc can you give me some pr...

Hello I am Contemplating breaking my volvo 340 It's a project I started but never finished Spec as follows Clio 1.8 engine with all 1.7 conversion parts and new 3 peice clutch and cable including proper flipped Inlet manifold to bring air filter at front Pre cut loom and extra idle peice by Adam360g...

Report to who ?

Your own little clubby.

Don't think people are interested in negativity.

You can modify. As long as it doesn't reduce the strength of what your modifying. Worst you'll get on a mot is Modified but not seriously weakened. Which is an advise. Not a fail. If the tubbing, welding ect is up to scratch. There's no problem. If you couldn't weld chassis every old car would be fu...

Cool that it saves weight but think you have missed out on an opportunity here to support pretty much everyone who modifies a volvo to fit wider wheels easier and nicer than rolling arches

Hi guys,

In need of a Cold start injector feed pipe.

It screws onto the end if the fuel rail and runs under the inlet manifold to the blue cold start injector.

Let me know if you have one as I am in desperate need

Cheers.

Hi guys,

Fitting a alloy fuel tank in the back of my car and will be fitting a fuel filler neck and cap through the lexan window,

Just wondering if I need to fit one of the one way breather valves or not because there is extra room because of the filler neck.

Any help appreciated.

Cheers

Basically I am trying to wire up my f7p engine and am a but stuck on the renix part. I have my 1.4 renix and I am left with the one three male connected plug, On the 1.4/1.7 engine conversion page it says join the pink yellow black on volvo loom to orange grey blue from volvo loom, I a, guessing you...

As said in title,

Selling h&r bolt on spacers as a pair, they are 25mm and about 3 months old

Still have original box

Comes with the spacers and shallow nuts needed to bolt onto car, use original wheel nuts to bolt wheel to spacer.

Looking for £80 quid plus p&p

Cheers.

All my wheel bearings are mint, I have only had the car a year but that's been daily driven/drifted and track days with low offset wheels. Doing a rebuild on the car just now so I am putting two rears in just for the sake of it being a fresh car. I think wheel size is each to there own and preferenc...

On a fully lowered car 195/50/15 tyres only need minimal body adjustments to properly clear. 195/45/15's would be perfectly fine but I wanted the gearing. 300's look high even when slamed, what they need is some good side skirts to make them look as low as they actualy are. So I can run my car as I...