Ali's drift 360 project
Sounds like turbo indeed, should have 0 in-out loose and next to nothing to other way, does not need much else indeed.Ali wrote:I suspect its just a knackered turbo as theres quite a lot of in-out and side to side play in the shaft, i'm just going to do the oil return again to be certain it can't be causing a problem
You did not check it before installing? Would clear return line possibility, but never harm to improve old one
- foggyjames
- *** V3M DONOR ***
- Posts: 9361
- Joined: 29 Jan 2004 04:20 am
- Location: Nottingham, UK
Significant shaft play isn't a good sign.
On another note, did I mention copper tubing for oil lines often being considered to be a bad thing? I don't know for sure, and it has been suggested that this is just internet rumour, but copper pipe has a reputation for splitting with age and the massive heat involved with a turbo.
I don't think we ever came to a definitive conclusion regarding what caused Suterman's 940 meltdown, but his copper pipe feed-line was a prime suspect. I think we'd all cry if that happened to your car. I'd suggest re-making it with something a little more hardy, if you're re-doing it anyway. I think the stock drain pipe is steel.
cheers
James
On another note, did I mention copper tubing for oil lines often being considered to be a bad thing? I don't know for sure, and it has been suggested that this is just internet rumour, but copper pipe has a reputation for splitting with age and the massive heat involved with a turbo.
I don't think we ever came to a definitive conclusion regarding what caused Suterman's 940 meltdown, but his copper pipe feed-line was a prime suspect. I think we'd all cry if that happened to your car. I'd suggest re-making it with something a little more hardy, if you're re-doing it anyway. I think the stock drain pipe is steel.
cheers
James
VOC 300-series Register Keeper
'89 740 Turbo Intercooler
'88 360 Turbo Intercooler
'85 360 GLT
'81 343 GLS R-Sport
'79 343 DL
'70 164
...and some modern FWD nonsense to get me to work...
'89 740 Turbo Intercooler
'88 360 Turbo Intercooler
'85 360 GLT
'81 343 GLS R-Sport
'79 343 DL
'70 164
...and some modern FWD nonsense to get me to work...
I've found the numbers of a couple of local fabricators that do alu welding so i'm going to give them a bell tomorrow, i'll try to get a pipe welded in at a decent downwards angle, the current copper one could be fine but i'd be majorly annoyed if I had to take everything apart again to swap the turbo plus the cost of killing another one.
And yeah, I did check the condition of the turbo and found there was play in it, was a little worried but was told by several people that there would be more play in it when it didn't have oil in there. Not the end of the world anyway, its not too many more hours work and might have it done ready to MOT next weekend, when paying £25 a week on insurance its making me get my arse into gear!
And yeah, I did check the condition of the turbo and found there was play in it, was a little worried but was told by several people that there would be more play in it when it didn't have oil in there. Not the end of the world anyway, its not too many more hours work and might have it done ready to MOT next weekend, when paying £25 a week on insurance its making me get my arse into gear!
Down to one car shocker! 1994 200sx S14 119k
- foggyjames
- *** V3M DONOR ***
- Posts: 9361
- Joined: 29 Jan 2004 04:20 am
- Location: Nottingham, UK
Perhaps a gnat's cock more play when dry, but it should still be pretty damn tight.
cheers
James
cheers
James
VOC 300-series Register Keeper
'89 740 Turbo Intercooler
'88 360 Turbo Intercooler
'85 360 GLT
'81 343 GLS R-Sport
'79 343 DL
'70 164
...and some modern FWD nonsense to get me to work...
'89 740 Turbo Intercooler
'88 360 Turbo Intercooler
'85 360 GLT
'81 343 GLS R-Sport
'79 343 DL
'70 164
...and some modern FWD nonsense to get me to work...
TBH shaft play has little effect on if its smoking or not, but obviously is a fair indication of turbo condition, as if bearings on its way, oil seals prob are too.
Ive seen (used! lol) turbos with well shagged bearings which had tons of play, so much so that they sounded like a air raid siren and the compressor wheel could be rubbed on the housing, but with NO smoke as seals wasnt fooked.
Smoke is from a leaking turbo seal, which can happen even with no bearing play.
Personally, if it was me id go with the rebuild kit idea, done it before, dead easy, and no need to re-balance if you not changing the parts that are balanced (ie wheels and shaft).
Only reason is a second hand turbo is just as likely to be fooked, as like said, shaft play only gives you a rough estimation on condition...
Ive seen (used! lol) turbos with well shagged bearings which had tons of play, so much so that they sounded like a air raid siren and the compressor wheel could be rubbed on the housing, but with NO smoke as seals wasnt fooked.
Smoke is from a leaking turbo seal, which can happen even with no bearing play.
Personally, if it was me id go with the rebuild kit idea, done it before, dead easy, and no need to re-balance if you not changing the parts that are balanced (ie wheels and shaft).
Only reason is a second hand turbo is just as likely to be fooked, as like said, shaft play only gives you a rough estimation on condition...
- foggyjames
- *** V3M DONOR ***
- Posts: 9361
- Joined: 29 Jan 2004 04:20 am
- Location: Nottingham, UK
Yaha...that's what we're seeing with Ryan's T3/T4 hybrid.....it's smoking like one of SteveP's girlfriends, but it's as tight as...er...where's Mick when you need him...Stavros wrote:Smoke is from a leaking turbo seal, which can happen even with no bearing play.
cheers
James
VOC 300-series Register Keeper
'89 740 Turbo Intercooler
'88 360 Turbo Intercooler
'85 360 GLT
'81 343 GLS R-Sport
'79 343 DL
'70 164
...and some modern FWD nonsense to get me to work...
'89 740 Turbo Intercooler
'88 360 Turbo Intercooler
'85 360 GLT
'81 343 GLS R-Sport
'79 343 DL
'70 164
...and some modern FWD nonsense to get me to work...
Nun?foggyjames wrote:Yaha...that's what we're seeing with Ryan's T3/T4 hybrid.....it's smoking like one of SteveP's girlfriends, but it's as tight as...er...where's Mick when you need him...Stavros wrote:Smoke is from a leaking turbo seal, which can happen even with no bearing play.
cheers
James
Sure seals can be good even bearing is gone, but quite often those go hand to hand unless turbo has been 'repaired' at some point.
- foggyjames
- *** V3M DONOR ***
- Posts: 9361
- Joined: 29 Jan 2004 04:20 am
- Location: Nottingham, UK
...or in this case was a cheap Chinese eBay-tastic hybrid 
cheers
James
cheers
James
VOC 300-series Register Keeper
'89 740 Turbo Intercooler
'88 360 Turbo Intercooler
'85 360 GLT
'81 343 GLS R-Sport
'79 343 DL
'70 164
...and some modern FWD nonsense to get me to work...
'89 740 Turbo Intercooler
'88 360 Turbo Intercooler
'85 360 GLT
'81 343 GLS R-Sport
'79 343 DL
'70 164
...and some modern FWD nonsense to get me to work...
I've been meaning to ask which way is bad for spindle movement, I have a erm, friend, with a turbo, that has a lot of in/out, but no side to side movement, and it doesn't blow smoke. See how it goes I guess, I was wondering if it could be recon'd.
'89(G) 340 GLE B172k
'03 S60 D5 SE, '91 (J) MX5, 1954 Cyclemaster
Ex:
'89(F) 340 GL F7R (ex B172k) - Fake -> SBKV 300 Runner Up 08, 12; '91(H) 340 GL B14.4E - Kar; '88(F) 360 GLT B200E - Jet -> BKV 300 Runner Up 09; '89(G) 360 GLT B200E - Beast
'03 S60 D5 SE, '91 (J) MX5, 1954 Cyclemaster
Ex:
'89(F) 340 GL F7R (ex B172k) - Fake -> SBKV 300 Runner Up 08, 12; '91(H) 340 GL B14.4E - Kar; '88(F) 360 GLT B200E - Jet -> BKV 300 Runner Up 09; '89(G) 360 GLT B200E - Beast
- foggyjames
- *** V3M DONOR ***
- Posts: 9361
- Joined: 29 Jan 2004 04:20 am
- Location: Nottingham, UK
I'm no expert, but I believe that means the thrust bearing is worn. If so, and if it's a T3, sounds like an ideal excuse to upgrade to a 360deg thrust.
cheers
James
cheers
James
VOC 300-series Register Keeper
'89 740 Turbo Intercooler
'88 360 Turbo Intercooler
'85 360 GLT
'81 343 GLS R-Sport
'79 343 DL
'70 164
...and some modern FWD nonsense to get me to work...
'89 740 Turbo Intercooler
'88 360 Turbo Intercooler
'85 360 GLT
'81 343 GLS R-Sport
'79 343 DL
'70 164
...and some modern FWD nonsense to get me to work...
- foggyjames
- *** V3M DONOR ***
- Posts: 9361
- Joined: 29 Jan 2004 04:20 am
- Location: Nottingham, UK
A thrust bearing usually exerts some pressure on a shaft to hold it in place in terms of "endfloat" - in this case, I think it means you can't move the shaft 'in and out'. There's usually one on the crankshaft too.
I'm honestly not exacty sure why anything other than 360deg ones ever existed, except that it means there's a break in the bearing (which looks a bit like a really fancy penny washer) to allow you to pull it off the shaft without dismantling it. The 270 looks like it has had a 90degree 'slice of pie' cut out of it. I guess a 360 is a full circle. We have a (270 deg...Ryan is stingey
) T3 rebuild kit downstairs...I'll take a piccy if anyone is interested.
cheers
James
I'm honestly not exacty sure why anything other than 360deg ones ever existed, except that it means there's a break in the bearing (which looks a bit like a really fancy penny washer) to allow you to pull it off the shaft without dismantling it. The 270 looks like it has had a 90degree 'slice of pie' cut out of it. I guess a 360 is a full circle. We have a (270 deg...Ryan is stingey
cheers
James
VOC 300-series Register Keeper
'89 740 Turbo Intercooler
'88 360 Turbo Intercooler
'85 360 GLT
'81 343 GLS R-Sport
'79 343 DL
'70 164
...and some modern FWD nonsense to get me to work...
'89 740 Turbo Intercooler
'88 360 Turbo Intercooler
'85 360 GLT
'81 343 GLS R-Sport
'79 343 DL
'70 164
...and some modern FWD nonsense to get me to work...
in-out movement is normal on some turbos.
youd be mad to recon a turbo even if it has side to side movement if it wasnt smoking, making scary noises, or had damaged blades.
270deg bearing= standard on most cars and is easy fitted.
360deg bearing= more surface area means can take the strain a little better but harder to fit.
pic...

youd be mad to recon a turbo even if it has side to side movement if it wasnt smoking, making scary noises, or had damaged blades.
270deg bearing= standard on most cars and is easy fitted.
360deg bearing= more surface area means can take the strain a little better but harder to fit.
pic...



